Drying cannabis with dehumidified air

Dehumidification of air with the Heat Pump Adsorption (HPA®) Air Dryer

 

Air can be dried to a low moisture level by adsorption or condensation, but also by a combination of these two! Drying or dehumidifying by means of adsorption concerns the binding of moisture in the air to a moisture-adsorbing material such as silica gel.

Description rotor

The centre of the HPA® Air Dryer is the rotor or adsorption wheel. This part consists for 82% out of a chemical bound silica gel that can adsorb moisture out of the process air that passes through the rotor. 

The structure of the rotor looks like a honeycomb pattern with a lot of small air channels. All these air channels make a big adsorption surface which takes care of the dehumidification of the air that passes the rotor; the silica gel adsorbs water from the air.

The same rotor can also release moisture during the regeneration process.

The HPA® Air Dryer is therefore divided in 2 levels. The rotor adsorbs moisture in the level for process air. The rotor turns in the level for the regeneration process where the rotor is being dried. After the regeneration process the rotor is ready to adsorb moisture again.

Regeneration of the rotor

The silica gel in the rotor cannot adsorb water unlimited. Nevertheless the adsorption and regeneration process is a continuing process.  To make the adsorption process a continuing process the construction of the rotor is designed to adsorb water at 75 or 50% of the total surface of the wheel (level for process air). 25 or 50% (depending the T° of the regeneration air) of the rotor is used for regeneration process (drying the rotor).

Rotor with 75-25 configuration; regeneration by hot air (150°C) from gasburner ad 25% of the rotor surface.

Rotor with 50-50 configuration; regeneration by warm air (60-80°C) from hot water battery or condensor.

By rotating, each part of the rotor will adsorb water and will later be dried by regeneration. The regeneration section is isolated from the adsorption section. By blowing hot air through the regeneration section, the adsorbed water will be removed from the rotor. The moist regeneration air will be evacuated through air-channels to outdoors.

Economically and modulating drying of air;

The HPA® Air Dryer principle with double heat pump and adsorption

HPA® Air Dryer with double heat pump
The HPA® Air Dryer is specially developed to create very dry air with an constant (low) temperature (20-25°C) of the process air. Process air is first being cooled, so water in the process air will condensate on the evaporator. After this, the process air at 100% HR will be dried to a low level by the Adsorption rotor. Because of high HR, the capacity of the adsorption rotor is at its maximum.   

First and second heat pump
Energy from cooling and condensation of the process air will be provided by the first heat pump to the condenser and liquid cooler. Air for regeneration (drying of the rotor) will be heated by this condenser and liquid cooler.

After passing the rotor the regeneration air is wet and warm. This air contains a lot of energy. By cooling the air and condensation of the water, the maximum of energy will be taken from the regeneration. By a second heat pump, this air will also being provided for regeneration. No external extra heating  is needed and all energy will be used; energy saving!

Recycling of process air for regeneration
The airflow for the process air is variable. When the airflow has reached its minimum and is still more than desired, the process air will return automatically to be used for regeneration. Again energy saving!!

 

Other versions
Depending on the capacity, the use and the number of running hours, Cannabis-drying.com can offer models in different versions that are economic for that situation. What makes the difference, is the way the process air is being cooled and the regeneration air is being heated;

Heat exchanger air/air
The hot process air (till 40-50 T°C) can be cooled down by a cross-flow air/air heat exchanger; The hot process air crosses the sucked in cold outside air by slats. The energy of the process air will be given to the colder outside air. The process air will cool down till 3 T°C above the temperature of the outside air. The heated outside air will be used for regeneration so that the subtracted energy can be used economically.

‘Chiller’ with cold and hot water
In the Heat Pump Adsorption ® Air Dryer, two water/air heat exchangers (radiators) can be placed. The sucked in process air will be cooled down in the radiator by using cold water. The regeneration air will be heated in the radiator by using hot water from the chiller.

Regeneration with hot water from the heater
If there is a central heating present, the regeneration air can be heated by a radiator by using hot water. The process air can be cooled down with an air/air heat exchanger (shown above).

Electrical regeneration
By using current delivered by windmills or solar panels, regeneration with electrical heating can be economic. The process air can be cooled down again with an air/air heat exchanger (shown above).